Log into the DD-WRT Web GUI Go to the Services tab DHCP Daemon should be enabled If there is no blank slot under "Static Leases", click Add Enter the MAC address of the client interface, the hostname of the machine, and the desired IP address for this machine. Note that you cannot reserve the same IP address for two different MAC addresses (e.g. both the wired and wireless interfaces of a device). By default, dd-wrt will hand out via DHCP its own IP as the Gateway. You can specify an alternate one like so: dhcp-option=br0,3,w.x.y.z or dhcp-option=br0,option:router,w.x.y.z A related but different solution is to create a DHCP setting that gives a static IP address to a certain MAC, but with a different Gateway address than the rest. DHCP options can be configured under via dhcp_option. Use an alternative default gateway, DNS server and NTP server. uci add_list dhcp.lan.dhcp_option= "3,192.168.1.2" uci add_list dhcp.lan.dhcp_option= "6,172.16.60.64" uci add_list dhcp.lan.dhcp_option= "42,172.16.60.64" uci commit dhcp / etc / init.d / dnsmasq restart. A list of options can DHCP Options. DHCP-Authoritative should be set when DD-WRT is the only DHCP server on its network segment (the most common setup). When authoritative, the DHCP server will immediately assign new addresses to clients that try to register using IPs from another network (rather than letting their previous lease time run out). U can easily use the dhcp server of DD-WRT (DNSMasq btw). Enable Use DNSMasq for DHCP in Setup/Basic Basic and go to Administration/Services. Enable the DNSMasq and add the following line in Additional DNS Options (not Additional DHCPd Options!): It takes 10 minutes to secure a DD-WRT wi-fi router. These are a security professional's recommended DD-WRT settings, including DD-WRT wireless settings. Follow these steps and I can almost guarantee you'll have the most secure network on your block, as well as unlocking some great capability from these devices. This option tells DNSMasq where the DHCP pool starts, ends, what the subnet mask is, and how long the lease will last. The arguments are specified in the following order: Start IP, End IP, Subnet Mask, Lease Time. The start IP, end IP, and subnet mask arguments should be IP addresses, and the lease time argument should be either minutes or hours (I.E. 1440m is 1440 minutes; 24h is 24 hours).

23/07/2010 · What do these 3 options on my router do? (DD-WRT Firmware)? "Use DNSMasq for DHCP" "Use DNSMasq for DNS" "DHCP-Authoritative" Also: "Force reconnect" "STP" "Multi Link" "PPP Compression" The top three are the major ones I want to know abo

The router is a Netgear R6300v2 running DD-WRT v24-sp2. My ISP uses DHCP for WAN and when I enable transparent bridging (after disabling wifi radio and DHCP server) the DD-WRT router has no internet access and I have to reset the modem and go through the walled garden process all over again. The router is set to auto-config DHCP for WAN. Setting the gateway IP the the modem's IP makes no

DD-WRT allows the use of all channels; this doesn't mean your client wireless adapter can support channels outside of its licensed region. How it works in DD-WRT: To configure your radio channels in the WebGUI you browse to the "Basic Settings" under the "Wireless" page on your DD-WRT router. If you have dual band router (ie. Two Radios inside the router) you will see two sections for

2) Allez dans « Setup »> « Configuration de base » et configurez les « Paramètres d’adresses réseau de serveur (DHCP) » suivants sous : DNS statique 1 = 8.8.8.8. DNS statique 2 = 8.8.4.4. DNS statique 3 = 208.67.222.222. Utilisez Dnsmasq pour DHCP = Vérifié. Utilisez Dnsmasq pour DNS = Vérifié. DHCP-Autoritaire = Vérifié Note - option 61 defintely seems to be missing from both DD-WRT and Voxel for the R7800. It would be nice to see it in either, becuase if the connection goes down I have to re-enter and run the command 19/04/2016 · Hi group, I have a LinkSys wrt54g router with DD-wrt install (Firmware: DD-WRT v24-sp2 (08/12/10) micro). DHCP is enabled. By default the DNS is This is an example of my Buffalo WHR-HP-G54 router (with DD-WRT installed) connected devices showing: Active (transmitting) wireless clients. Clients whose DHCP Lease Time has not expired (configured to 180 minutes in my case). As I use to enter the device via SSH, I would like to develop some script to obtain the second table: DHCP Clients List. I am using DD-WRT v24SP1 on my Linksys WRT 54GL router and I am trying to get the build in DHCPd server to also send the ip address of my TFTP server. In general I need to be able to add option 66 and option 150. I have tried to find other topics that might describe this topic but was unsuccesfull.

Il est ainsi préférable d’opter pour un VPN qui n’est pas situé dans votre pays !|Mais l’utilisation d’un Dd Wrt Dhcp Server ne concerne pas que le téléchargement frauduleux. En effet, les réseaux privés virtuels apportent également une sécurisation poussée des dépendance Internet pour réaliser des paiements en ligne. L’utilisation d’un logiciel VPN s’avérer pratique

Il y a 11 heures

Antenne fourni par la societé Infracom avec le WRT 54GL en DD WRT qui conseille de cabler le WAN sur une entrée BOX et ca fonctionne . Antenne hotspot -----WRT 54GL avec DD WRT ---port WAN qui

19/04/2016 · Hi group, I have a LinkSys wrt54g router with DD-wrt install (Firmware: DD-WRT v24-sp2 (08/12/10) micro). DHCP is enabled. By default the DNS is